SYSTÉMY POŽIARNEHO ROZHLASU EN 54-16 arrow VM-2240

VM-2240

VM-2240
VM-2240 - prgramovateľná ústredňa požiarneho rozhlasu, 240 W/100V, 5 zón, možnosť prepojením viacerých ústrední - max. 8 ústrední, 40 zón, max. 4 mikrofónové pulty RM-200M, možnosť doplnenia o EV-200 (digitálny hlásič správ) a SV-200MA (kontrola liniek).
 
Cena: 962,90 € bez DPH 29 008,33 Sk bez DPH
1 155,48 € s DPH 34 809,99 Sk s DPH

DATA Library    \"web\"Stránka výrobcu       Katalogový list SK

VM-2120/VM-2240
Power Requirement VM-2120: AC; mains, 50/60 Hz
DC; 24 V DC/7.5 A, M3.5 screw terminal,Barrier distance: 8 mm, Applicable cable diameter: AWG22 - AWG14
VM-2240: AC; mains, 50/60 Hz
DC; 24 V DC/15 A, M3.5 screw terminal,Barrier distance: 8 mm, Applicable cable diameter: AWG22 - AWG14
Speaker Component 12cm full-range speaker
Power Consumption on AC Mains VM-2120: With no signal present; 37 W
Under normal operating conditions according to
EN60065; 1998 sec. 4.2: 107W
With rated output signal: 201W
VM-2240: With no signal present; 54 W
Under normal operating conditions according to
EN60065; 1998 sec. 4.2: 225W
With rated output signal; 549W
Current Consumption
on 24V DC Power Input		 VM-2120: With no signal present; 0.7A
Under normal operating conditions according to
EN60065; 1998 sec. 4.2: 2.1A
With rated output signal: 5.2A
VM-2240: With no signal present; 1A
Under normal operating conditions according to
EN60065; 1998 sec. 4.2: 5A
With rated output signal; 14A
Rated Output VM-2120: 120W
VM-2240: 240W
Output Voltage/Impedance VM-2120: 100 V/83 Ω, 70 V/42 Ω, 50 V/21 Ω
(selectable by the internal wiring change)
VM-2240: 100 V/42 Ω, 70 V21 Ω, 50 V/10 Ω
(selectable by the internal wiring change)
Frequency Response 50 - 16,000Hz
Distortion Under 1%
Signal-to-Noise Ratio Over 60 dB
Tone Control Bass: 100 Hz ¡Þ10 dB, Treble: 10 kHz ¡Þ10 dB
(Inputs 1 - 3 and BGM individually adjustable.)
Remote Microphone/ Expansion Amplifier Connection 2 RJ45 female connectors for connecting the RM-200M Remote Microphone and the VM-2120 or VM-2240 unit used as an expansion amplifier. Maximum distance: 800 m in total, Link cable: Category 5 shielded Number of connectable RM-200M's: Up to 4 Twisted-Pair straight cable (TIA/EIA-568A standard)
Inputs 1 ? 3 -60 dB*1 (MIC)/-10 dB*2 (LINE) (changeable), 600 ?, electronically balanced*1, combined XLR connector (female)/phone jack (Only Input 1 is additionally equipped with DIN connector*3.)
Telephone paging input Push-in terminal block*4Voice sound: -10 dB*1, 10 kΩ, electronically-balanced input with shield terminal*2
Control: No-voltage make contact input, open voltage: 30 V DC, short-circuit current: under 0.1 A
BGM 1 - 2 -20 dB*1, 10 kΩ, RCA pin jack, monaural (internally mixed)
Power amplifier input 0 dB*1, 10 kΩ, RCA pin jack
External speaker line input 100 V line, for All-Zone Broadcast (This input is selected when the "Unit's broadcast cutoff" control is activated.)
Speaker outpu Plug-in screw connector*5 5-zone selector with attenuator (all zones simultaneously selectable)
Direct speaker line output Direct output from the power amplifier output transformer (attenuator bypassed), Plug-in screw connector*5
Line output 0 dB*1, 10 kΩ, RCA pin jack
Recording output 0 dB*1, 10 kΩ, RCA pin jack
Preamplifier output 0 dB*1, 10 kΩ, RCA pin jack
Control Input For controlling Inputs 1 - 3, Push-in terminal block
No-voltage make contact input, open voltage: 3.3 V DC, short-circuit current: under 1 mA
Control Input and Output D-sub connector (25-pin, female)
Input: No-voltage make contact input, open voltage: 3.3 V DC, short-circuit current: under 1 mA
Output: Open collector output, withstand voltage: 30 V DC, control current: under 10 mA
(1)External control input
•Activation of messages*6
•Activation of power
•Activation and stop of Emergency Broadcast
•Unit's broadcast cutoff (when activated by an external emergency equipment)
(2)Status output
•Irregularity of communications with the Remote Microphone and an expansion amplifier
•AC power condition
•DC power condition
•Irregularity of the sound source of the Voice Announcement Board
•Failure (FAULT) indication on
•Power switch on
External Attenuator Control Output Plug-in screw connector*5, relay, no-voltage make contact output, transfer type, withstand voltage: 30 V DC, 125 V AC, contact current: under 7 A (DC), under 7 A (AC)
Surveillance Input and Output*7 D-sub connector (25-pin, female)
Input: No-voltage make contact input, open voltage: 3.3 V DC, short-circuit current: under 1 mA
Output: Open collector output, withstand voltage: 30 V DC, control current: under 10 mA
Power Supply 24 V DC/0.1 A, for supplying power to an optional Amplifier
Control Unit RU-2001/2002, push-in terminal block*4
Chime Tone Built-in chime: 2-tone chime/2-tone chime (fast repeat)/4-tone chime (Up)/ Single-tone chime/4-tone chime (Up & Down)/Gong/off
Voice Announcement Board sound source: Pre-recorded chime*6
Function Two units stacking (VM-2120 or VM-2240)
Emergency broadcast (sequential control)
Broadcast priority control Surveillance (failure detection) function*7
Power supply to only one Remote Microphone (RM-200M) Line resistance: Under 24 Ω (one way)
Operating Temperature 0ºC to +40ºC
Finish Panel: ABS resin, dark gray, paint
Case: Steel plate, dark gray, paint
Dimensions 419 (W) × 143.3 (H) × 355.7 (D) mm
Weight VM-2120: 12.5kg
VM-2240: 14.5kg
Accessories Power cable (2m) × 1
Miniature type time-lag fuse × 1
Name label × 1
Volume cover × 4
Options Rack mounting bracket: MB-36, Input transformer: IT-450, Voice announcement board: EV-200,
Surveillance board: SV-200M

*1 0 dB = 1 V
*2 Can be transformer-balanced with the addition of an optional IT-450 input transformer.
33 For connection of the Paging Microphone PM-660D with a remote control switch.
*4 Usable cable diameter: AWG26 - AWG20, 0.5 mm2.
*5 Usable cable diameter: AWG24 - AWG12, 2.5 mm2.
*6 An optional EV-200 Voice Announcement Board is required. The chime sound source must be pre-recorded into a CF (CompactFlash) card to be inserted into the EV-200 Board.
*7 An optional SV-200M Surveillance Board is required.



RM-200M (Remote Microphone)
Power Requirement 24 V DC (Operating range: 14 - 28 V DC)
Power input jack: Non-polarity type
Usable power input plug*2: Outer diameter ø5.5 mm, inner diameter ø2.1 mm, length 9.5 mm
Current Consumption 100 mA maximum
Distortion Under 1%
Frequency Response 100 - 20,000 Hz
Signal-to-Noise Ratio Over 60 dB
Audio Output 0 dB*1, 600 Ω, balanced
Microphone Unidirectional electret condenser microphone
Speaker Control Zones 1 - 5 or Zones 1 - 10 (2 stacked amplifiers connection),
Groups 1 - 2, and All-Zone Broadcast
Emergency Broadcast Activation of Emergency Broadcast (pre-recorded announcement*3 or live microphone announcement) by Emergency Broadcast Switch
Voice Message Control Activation of 5 messages*3
Volume Control Microphone volume control
Connection Cable and Connector Category 5 STP cable, RJ45 connector
Finish ABS resin, bluish gray
Dimensions 190 (W) × 76.5 (H) × 215 (D) mm
(Gooseneck microphone excluded)
Weight 750g
Accessory Link cable (3m) × 1
*1 0 dB = 1 V
*2 Use the AC adapter AD-4800 optionally available as our service component.
*3 An optional EV-200 Board must be mounted in the VM-2120 or VM-2240 Amplifier.
The voice messages must be pre-recorded into a CF (CompactFlash) card to be inserted into the EV-200 Board.




Viac kategórií

ATEIS (18)
TOA EN 54-16 (49)
BOSCH (15)

 
Konverzný kurz: 1 EUR = 30,1260 SKK